PowerPoint Presentation On RSRTC

PPT On RSRTC
 Download

RSRTC Presentation Transcript:

2.Introduction Of R.S.R.T.C.
RSRTC was established on 01st October 1964 and is the largest provider of intercity bus transportation in Rajasthan.  
RSRTC is currently transporting about 10.74 lack passengers daily and operating on routes connecting 32 districts of Rajasthan and neighboring states.   
The Network of R.S.R.T.C. is spread all over Rajasthan and other states providing all sorts of service to general public.
These services are provided by R.S.R.T.C. by its own fleet in which buses are purchased from various manufactures like TATA, ASHOK LEYLAND etc.
For any faults in buses, R.S.R.T.C. has established workshops in different cities like in Jaipur. If a bus has been damaged by an accident of a bus which has come from regular maintenance each and every part of it, from tyres to steering, propeller shaft to piston are inspected.                                                                       

3.BUS SERVICES
Type of bus services:- There are various types of services offered by RSRTC. 
1.volvo air-conditioned services.
2.Sleeper A/C coach.
3.Air conditioned(Pink line services).
4.super deluxe(silver line services).
5. Long distance express and night services (Blue line services).
6. Interstate services.
7. Ordinary services.
8. Mela services
9. CTS services
10.Sleeper non -A/C coach.

4.Body section:-
Body is the just like of the cover for the chassis & it is upper structure of Vehicle. In this section parts of buses are repaired and separated from it. The damaged parts are maintained again. The Glasses are replaced and tyres are retreated. The bends in the body are removed.
Body shell is made of following parts:-
1. Front Doors
2. Rear Doors
3. Front Frame, Cross Beam and Front wheel.
4. Right Side Panel with Fenders
5. Left side Panel with Fenders
6. Front Panels
7. Roof Panels
8. Rear Lower Panel

5.Chassis section:-
     Chassis section is the French term used to denote the frame or main structure of a vehicle. In Chassis section various assembly are disassembled and sent to their respective sections for repairing, after repairing have been carried out they are sent back to chassis section where they are again mounted on Chassis.

                                     Chassis is a vehicle without body. This term is used to describe the whole vehicle excluding body. Many components like engine and radiator , wheels and tyres , steering system , axles , controlling system like braking , suspension etc. are mounted on Chassis frame. In other words Cassis is sometime referred as “ BACK BONE “ of the vehicle.

6.Differential Assembly :- The differential assembly in a rear-wheel drive vehicle has three functions. The first, and most obvious, is to redirect the power flow to drive the rear wheels. The power flow must make a 90° turn between the drive shaft assembly and the rear wheels. This is accomplished in the differential assembly by the drive pinion and ring gears. The second function of the differential assembly is to multiply engine power, reducing speed at the output in the process. If there were no gear reduction (1:1 gear ratio), the vehicle would accelerate very slowly.                                                                                                                               

7.Minor Section:-
In minor section dissembling cleaning, checking repairing or replacement is done according to the need of pant. Thus this sector is very important for the proper functioning of buses. Minor Assembly Components are:-
1. Clutch and Pressure Plate:-A Clutch is a machine member used to connect the driving shaft to a driven shaft, so that the driven shaft may be started or stopped at will, without stopping the driving shaft. Clutches allow a high inertia load to be stated with a small power.
                                                                                               A clutch is a mechanical device that provides for the transmission of power (and therefore usually motion) from one component (the driving member) to another (the driven member) when engaged, but can be disengaged.

7.Pressure Plate:-
The pressure plate is an integral factor in the function of an automobile’s manual transmission. The pressure plate pushes the clutch disc, sometimes called the clutch plate, against the constantly spinning engine flywheel. The clutch disc, therefore, is either stationary or rotating at the same speed as the flywheel. Friction material, similar to that found on brake pads and brake drums, causes the clutch disc to spin at the same speed as the engine flywheel. It is this friction between clutch disc and flywheel that allows the engine torque to drive the wheels

8.Dismantle Section:-
In this section dismantling of Chassis parts and engine is done. After this damaged parts are sent to different section related to them for inspection, cleaning, repairing and replacement of broken parts.

9.Radiator Section :-
Radiator is a device for having a large amount of cooling surface and facilitate to pass large amount of air through it, so that the water circulating through its tubes cooled efficiently.
In R.S.R.T.C. buses radiator are made up of aluminum because of its good heat conductivity, lightness, cheapness and easy of making and repairing.

10. Washing Section :-
In this section washing of R.S.R.T.C. buses is done by an automatic washing system. Side brushes wash front, sides and rear of the bus. The rotating brushes are freely suspended and move inward or outward according to the vehicle dimensions.